Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

Zipp 11-speed Freehub Kit for 177 Hub
$97.38 - $140.00
Zipp Speed Weaponry Freehub Bodies - Material: Aluminum
Wheels Manufacturing Inc. Freewheel/BB Spacer
$19.95
Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10
Wheels Manufacturing Inc. Outer Axle Nut
$1.50 - $6.25
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
WTB TCS Rim Tape
$14.95 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
Stan's NoTubes Neo Bearing Kit
$12.50 - $29.00
Replacement bearings for Stan's NoTubes Neo hubs. Includes 2 bearings. - 26mm OD x 15mm ID - 7mm thick
Stan's NoTubes Neo Speedsync Freehub
$130.00
Stan's original Neo hub has evolved to be stronger and more reliable than ever. The additional stress of larger cassette cogs, more capable bikes, and even more challenging trails led to the creation of the Neo with Speedsync. This CNC machined Speedsync freehub is a direct replacement for your Neo hub and includes pawls, springs, pawl retaining ring, and 2 red freehub spacers. Bearings are pre-installed. Note: - Singlespeed freehub cannot be used to convert a hub originally set up with a Shimano or Sram XD freehub to SS. This freehub is only to be used with Stan's Neo SS hubs. - OneUp freehub WILL NOT WORK with a SRAM cassette or Shimano cassette without a One Up Shark Cluster.
Stan's NoTubes Rim Tape
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Stan's NoTubes Tubeless Valve Stems
$16.00
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Stan's NoTubes Universal Schrader Tubeless Valve Stems 32mm
$16.00
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.
Salsa Deadbolt Thru-Axle
$49.00
The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications
Salsa Deadbolt Ultralight Thru-Axle
$39.00
The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6mm hex wrench required for installation
SRAM Maxle Stealth Rear
$31.00 - $82.00
Who knew we could make a thru axle disappear? The Maxle Stealth offers a light, low profile alternative to Maxle Lite. Features - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench
Robert Axle Project Rear Lightning Bolt-On Thru Axle
$48.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
Robert Axle Project Trainer Thru Axle
$54.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Problem Solvers Thru-Axle/QR Adaptor
$19.99
Thru-Axle hub adapters allow the use of 100 mm front thru-axle hubs in 100 mm QR forks. -Allows the use of modern thru-axle wheels in forks designed for quick-release compatible hubs -100 mm front hub spacing only -CNC-machined AL-6061
Mavic Rear Axle Adapters - QR (Center Lock)
$13.50
On today's MTB frames, there are many dropout diameter and width standards. Most Mavic wheels can be fitted with specific adapters to match your wheelset with your frame. - Converts Mavic mountain rear hubs to Quick Release - One pair of adapters required for each hub to be converted
DT Swiss Disc Brake Rotor Adaptor Center Lock/6-Bolt
$17.80
DT-Swiss Center Lock Adaptor. Allows 6-bolt rotors to be used on Center Lock hubs. - Rotor thickness between 1.8mm and 2.2mm - Easy assembly and only 29g - Made in Switzerland by DT Swiss - 230mm version accepts all rotors up to 203mm diameter - 160mm version accepts all rotors up to 160mm diameter
DT Swiss RWS MTB Rear Thru Axle - X-12
$36.90
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Conical X12 washer, compatible with Syntace X-12 system - Thread Pitch: 12 x 1.0mm
DT Swiss Tubeless Ready Rim Tape
$21.50 - $23.40
DT Swiss tubeless-ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type setups. - Durable adhesive tape works as a rim tape and airseal
Zipp 11-Speed Freehub Kit for 2013 - Current 188 Hub
$136.00
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
Zipp 77/177 Disc Conversion Caps
$17.10 - $28.00
Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.
Zipp AM Rim Tape
$7.00
Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.
Zipp CeramicSpeed Freehub Body and Bearing Kit: 177 SRAM/Shimano Cassette Hub Body
$363.00
- Kits include Freehub body with CeramicSpeed bearings pre-installed for easy installation onto the wheel - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings
Zipp CeramicSpeed Freehub Upgrade Kit ZIPP 177
$363.00
- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed
Zipp Cognition Freehub Kit
$116.30 - $133.00
Freehub bodies for Zipp Cognition hubs.
Zipp Conversion Kit 11-speed to Track 188 Black
$205.00
Zipp Speed Weaponry Rear Axle Conversion Kits - Converts a road disc into a track disc rear - Fits black 2013 188 V8 disc hubs only - Fits Zipp 900 and Super-9 Discs
Zipp Decal Set
$20.00
These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.
Zipp Disc Wheel Valve Cover Patches
$6.00
A simple solution for completing the Zipp aerodynamic package by covering the valve access hole on most disc wheels. Black, self-adhesive oval patches with the Z logo, in a package of five.
Zipp Dual Wheel Bag
$154.00
The most important transitions isn't T1 or T2; it's the transition from home to the race, so protect your wheels with Zipp's Wheel Bag. It's designed to hold two wheels inside a padded pocket, and it features a stuff sack for race supplies.
Zipp Freehub Kit 11/12 Speed XD
$100.00
Wheel Freehub Kit—(Includes Bearings & Pawls) 11/12 Speed XD—X0 HUBS/RISE 60 (B1)/ROAM 30/ROAM 40/RAIL 40/RISE XX/ROAM 50/60 (B1) Compatible With: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1
Page 1 of 9 Next page