Parts

- Durable CrMo construction with 4-pawl internal engagement system - Fits left-hand (LH) threaded hubs only (allows mounting drivetrain on left side of bike for grinding on the right side) - Maintain with petroleum based lubricant (no wax/Teflon)

- Chromoly steel with black oxide finish - 1.37" x 24tpi right hand thread - Requires a cog lockring (sold separately) - Compatible with 1/8-inch chains

• Perforated leather top • Ti/CrN rails • 290 grams

The 612 Track Crank is an extremely stiff and strong 144mm BCD track crank. It’s at home as much on the busy avenues of your city as it is on the boards of the velodrome. All-City sweats the details, so the 612 (Minneapolis’ area code) is cold-forged, resulting in a tight grain structure. The upshot is that it’s strong, which means more riding and less worries for you. It utilizes the classic JIS square taper spindle and comes with a color-matched, 46-tooth, 1/8th chainring.  - Recommended Spindle Length: 110mm - Spindle Interface Type: square taper JIS - Bolt Pattern: 5-bolt - BCD: 144mm - Chain Compatibility: 1/2-inch x 1/8-inch - Weight: 726g w/ ring and bolts - Bottom bracket and retaining bolts not included

Art Gecko is our new grippy polyurethane rubber bar tape with a colorful artistic patter on the drops. This pattern is called a tri-color tessellation. When wrapped from the bottom it fades to black about where the brake levers mount. - Artistic pattern, 9 colorful choices - Color below the drops, black up top - Great feel, Polyurethane rubber surface - 220 cm rolls, plenty of length - Nice flat wrap - 92 grams including the plugs

Slip Avid's Rim Wrangler 2 Brake Pad Inserts into your Rim Wrangler 2 cartridges (sold separately) for excellent braking no matter the conditions. The easy-to-use cartridge design makes swapping pads a breeze. They're designed for use with linear-pull brakes.

The squeeze of our levers is what dreams are made of. Most of our levers can be swapped to be run either front or rear, which is convenient if you like to your brakes reversed and a Godsend if you bust a lever in the middle of the woods. Avid levers are easy to install, simple to set up, and a pleasure to pull. - ReachAdjustment -- Qwik-Adjust Barrel Adjuster Bend Zone

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

Avid's Rear 170mm Post Bracket Hardware Kit has everything you need to mount a 170mm rotor (sold separately) to the back of your bike. Kits include mounting bolts and a 30mm post mount spacer for rear brake installation.

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

The Box Four cassette adapts our Prime 9 philosophy of durability, simplicity, and reliability at a great price point. All cogs are stamped from steel, given our durable black coating and then the larger cogs are pinned to each other with spacers for easy installation.

- Low-rise Black Ops chromoly BMX handle bar - 30-inch width with a 6-inch rise - Wide and low - Clamp Size: 22.2mm - Material: Chromoly

Campagnolo Ultra Torque Cup and Bearing Kits. Includes 2 bearings and 2 seals. - Kit includes 2 bearings and 2 seals

Thanks to Campagnolo's Ultra-Drive system, the Veloce Cassette offers precise, fluid shifting. The teeth are carefully machined and treated for flawless gear changes and outstanding durability. Plus, the special cog patterns interface perfectly with the rest of Campy's drivetrain components for outstanding shifting.

Campagnolo's Record 11-Speed Chain is the right choice for Campagnolo 11-speed drivetrains. This fine chain is engineered for excellent strength, long wear and brilliant shifting thanks to a unidirectional design and an anti-friction treatment that lets it glide across your cassette. It also boasts hollow pins to keep your bicycle as light as possible.

Compatible only with Record or Chorus square taper cranks. Features three cartridge bearings and a chromoly steel spindle. - 3 sealed cartridge bearings, 2 on the drive side, 1 on the non-drive side - Removable cups are machined from 7000 series aluminum - Unique taper is not compatible with Shimano - Weight: 220 grams

- Stock for 07-08 Record and Chorus 10-speed compact and standard cranksets - Ultra-Drive ESP alloy chainrings with anti-friction treatment and ramps/pins - *Campagnolo compact rings are Ultra-Torque specific BCD - Color: Grey

Campagnolo's Chorus Cassette offers precise, fluid shifting for your 11-speed drivetrain. The teeth have been exquisitely engineered and machined from steel, then coated with a nickel-chrome surface treatment and mounted on an aluminum carrier for flawless shifts and excellent durability.

Shim spacers can be placed between bearing and compression cover in IS headsets to fine tune the fitment.

• Replacement hoods for road brake levers with traditional, non-aero cable routing • Soft, tacky rubber for a sure grip • Available in black or brown

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

Bearings for Cane Creek AER headsets. - Aluminum Bearing

Hellbender bearings have an improved seal structure and are cross compatible with Cane Creek headsets.

Add another braking option to your road or cross bars with Cane Creek's Cross Top Brake Levers. They are a great way to gain more control on technical cyclocross courses by enabling braking from the tops of the bars.

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek's 40-Series headsets. • Technical Description: IS41/28.6/H9/K • Top Type: IS - Integrated • Top Head Tube Inside Dia.: 41.1mm • Stem Clamp Dia.: 28.6mm • Top Stack Height: 9mm (Short), 15mm (Tall) • Top Bearing Type: Black Oxide, Sealed • Material: 6061 aluminum • Weight: 37g

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek headsets. The 10 Series has light, tough and beautiful machined 6061 T6-aluminum cups, Cane Creek's corrosion-resistant black-oxide angular-contact bearings and quality seals throughout to keep the grease in and the dirt out.

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek headsets. The 40 Series has light, tough, and beautiful machined 6061 T6-aluminum cups that are internally relieved for even more gram shaving. You also get Cane Creek's corrosion-resistant black-oxide sealed bearings and quality seals throughout to keep the grease in and the dirt out, including Cane Creek's Clip Seal that completely seals the top assembly.

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek's 40-Series headsets. • Technical Description: IS41/28.6/H9/K|IS52/40/H1 • Top Type: IS - Integrated • Top Head Tube Inside Dia.: 41.1mm • Stem Clamp Dia.: 28.6mm • Top Stack Height: 9mm (Short), 15mm (Tall) • Top Bearing Type: Black Oxide, Sealed • Bottom Type: IS - Integrated • Bottom Head Tube Inside Dia.: 52.1mm • Crown Race Seat Dia.: 39.79mm • Crown Race Type: Steel, Face-Sealed • Bottom Stack Height: 1mm • Bottom Bearing Type: Black Oxide, Sealed • Material: 6061 aluminum • Weight: 87g

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek's 40-Series headsets. • Technical Description: ZS44/28.6/H8/K|ZS56/40/H4/K • Top Type: ZS - ZeroStack • Top Head Tube Inside Dia.: 44.00mm • Stem Clamp Dia.: 28.6mm • Top Stack Height: 8mm • Top Bearing Type: Black Oxide, Sealed • Bottom Type: ZS - ZeroStack • Bottom Head Tube Inside Dia.: 55.95mm • Crown Race Seat Dia.: 39.79mm • Crown Race Type: Steel, Face-Sealed • Bottom Stack Height: 4mm • Bottom Bearing Type: Black Oxide, Sealed • Material: 6061 aluminum • Weight: 109g

The Absolute Best Well over a decade ago, we set out to make the best premium headset on the market. With our 110 Series, we did just that, utilizing optimal materials, the most effective seals and the best aesthetics. With the flexibility to purchase complete assemblies or separate Tops and Bottoms, tops are available in either short (9mm) or tall (15mm) stack height bearing covers, the 110-Series offers a premium solution for nearly all straight and tapered configurations on the market today. From Integrated (IS) Tops to External Cup (EC) Conversion Bottoms and everything in between, you can mix and match your headset purchase to best meet your needs. - Technical Description: 110-Series IS41/28.6/H9 | IS52/40 - Top Type: IS - Integrated - Top Head Tube Inside Dia.: 41.1mm - Stem Clamp Dia.: 28.6mm - Top Stack Height: 9mm - Top Bearing Type: Top-quality, sealed stainless steel bearings - Bottom Type: IS - Integrated - Bottom Head Tube Inside Dia.: 52.1mm - Crown Race Seat Dia.: 39.79mm - Crown Race Type: Aluminum, Dual-Seal - Bottom Stack Height: 1mm - Bottom Bearing Type: Top-quality, sealed stainless steel bearings - Material: N/A - Weight: 79.48 grams

These baseplates are the foundation that keeps Chris King headsets turning with legendary smoothness. Manufactured from high-quality stainless steel or titanium, Chris King makes replacement baseplates for all standard sizes and a number of ingenious solutions for those that need something a little special to make their headset work. - Engineered and manufactured in Portland, Oregon USA - High-quality stainless steel and titanium baseplates available for all standard Chris King headset sizes - Titanium baseplates are available in 1-inch and 1 1/8-inch sizes only - Devolution baseplates are a stainless steel solution that allow King headsets to adapt to a wide variety of steerer tube sizes - King Stainless Steel baseplates are available in undersized and oversized versions for irregular steerer tube sizes - 30.0mm ID/40.5mm OD for post-April 1995 1-1/8" Headsets - 30.0mm ID/44.0mm OD for pre- April 1995 1-1/8" Headsets

Chris King DropSet 3 Headset. - Crown Race: 30 - S.H.I.S. Stem Clamp Diameter: 28.6 Threadless - Bearing Type: Cartridge - S.H.I.S Lower: IS52 - S.H.I.S Upper: IS41

Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs

Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals

Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet, and Quattro pedals. They're made from solid brass for crisp entry and exit, and top-notch durability.

Crank Brothers' Zero Float Cleats offer no pedal float for greater pedaling efficiency. They're made from solid brass for crisp entry and exit, and top-notch durability. - Weight (pair): 30 grams - Shoe compatibility: SPD - Release angle: 15 degrees

Crank Brothers' Quattro 3-hole cleats let you use Crank Bros. pedals with your road shoes. The cleat and walking plate mount directly to shoes that use a traditional 3-hole mounting setup.

Choose to ride flat or clipped in for city commutes and casual rides around town. This hybrid composite pedal with its 2-sided entry allows you to do both. It features premium bearings and a double seal system, diamond plate pads for traction, and molded pins and ribs for grip. - Premium brass cleats with shims included - Q-factor: 57mm - Release angle: 15° / 20° - Forged 435 Chromoly steel spindle - 300 series stainless steel spring - 5-year warranty - 331g per pair

Competition-oriented and customizable for refined fit, feel, and power transfer. Details - Durable alloy body - Durable cast steel wings - Integrated traction pad technology to optimize the shoe/pedal interface - Ribbed body for better traction when unclipped - Chamfered edges to reduce rock-strikes - Hex alloy endcap and bashguard - 4-sided entry / superior mud shedding - Customizable float & release angle - Premium bearings & double seal system Specs - Body Material: 6061-T6 aluminum - Cleats: Premium brass cleats with shims included - Endcap: Hex alloy - Inner Bearing Type: Igus LL-glide bearing - Max Rider Weight: No restriction - Outer Bearing Type: Enduro cartridge bearing - Q-factor: 52mm - Release Angle: 15° / 20° - Spindle Material: Forged scm 435 chromoly steel - Spring Material: 300 series stainless steel - Warranty: 5 years - Weight: 320g per pair - Wing Material: 17-4PH stainless

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 18307 Bearing

PR1400 OXiC Disc Brake Pads - Brake pad inserts are made by Swiss Stop

Excellent modulation, cooler temperatures, and great wet weather brake performance. The Black Prince brings the feel of braking on alloy wheels to carbon wheels. - Pad Type: Replacement Insert-Cartridge - Intended Brake Type: Caliper - Rim Compatibility: Carbon

Torque caps increase the contact surface area between frame and fork resulting in a stronger and stiffer interface and more control. - Allows for easy installation on Rock Shox Torque Cap compatible forks

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss Star Ratchet Kit - 24T

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss 18t Superlight Star Ratchet Kit: Includes Springs and Grease

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss Star Ratchet Kit - 54T

The grip of choice for World Cup-style assassin and gloveless wonder, Sam Blenkinsop, the KNUCKLEDUSTER embodies our attention to detail and our focus on function! Not only have we developed our TRC rubber blend that gives you remarkable grip with incredible durability, the KNUCKLEDUSTER also features a tapered internal sleeve that you have to tap onto your handlebar for full engagement. This tapered sleeve feels like it is already locked into place once fully tapped onto the bar and, coupled with a single bolt lock-on clamp, you will not develop any play. The body of the grip combines the best elements of a half-waffle, mushroom ribbing, and an ergo feel in a stunning package. Featuring a mushroom pattern to minimize vibration, the true magic of the KNUCKLEDUSTER lies in the V channel chevron ribs that ergonomically fill the swell of your palm and then seamlessly transition to a recessed half waffle on the underside. Why is this magic? All half waffle patterns are outboard and are notorious for creating hot spots on long rides. By designing the top to seamlessly transition to a recessed half waffle pattern, your fingers sit perfectly into the grip and allow you full control even in the roughest of conditions without being plagued by hot spots or blisters. The KNUCKLEDUSTER grips truly are an "all day grip" that allow you to keep it Pinned Wide Open at all times! - The benchmark in grip design - DIRT MAG Top 100 Product for 2018 - Featuring DEITY TRC rubber compound for exceptional durability - Tapered inner sleeve to ensure perfect contact with the handlebar - Single clamp design with forward-facing bolts that feature Loctite - Lasered black-ano 6061-T6 aluminum clamps - Short and wide rib design for added comfort with no side-to-side play - Half-waffle recessed design for added control without hot spots - Chevron v-channel design for your palm swell to give an ergonomic feel - Seamless transition through the end of grip for comfort - 132mm length with 32mm outer diameter - Intended use: All MTN / Enduro / DJ / Slopestyle and DH - 101 grams for the set

The DEFTRAP will revolutionize what you should expect from a nylon composite pedal with it's non-offset symmetrical platform to offer added stability behind the spindle, a true concave pedal profile so your feet sink into it, 10 total pins (8 replaceable cr-mo pins and 2 molded pins), our tried and true sealed bearings and DU bushing system, and top tier nylon and glass fiber composite material to create a pedal that feels unlike anything on the market. With a focus on ride quality, increased foot support, added stability, leading traction, ability to skim over rocks, and even coming in 10 colors-the DEFTRAP will challenge you to rebel against the conventional perception that a value pedal cannot rival the best pedals on the market!

Dimension Toe Clips and Straps Set. Includes: - 4 bolts - 4 nuts (washers included) - 2 nylon toe straps - 2 toe clips

Dimension Mountain Basic Pedals. - Molded nylon 1-piece, caged-type pedal with reflectors - Accepts toe clips - Hang tag packaging - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 330g

Dimension Freewheels are excellent drivetrain component replacements. With smooth shifting performance and durable construction, they'll help breathe new life into older bikes. - A must have in any bicycle service department - One-piece design - Shimano index compatible - Works with most friction shifters - Suitable for use with e-bike drivetrains

Dimension Chainrings. - No ramps, pins, or shift aids

Dimension Mountain Compe Pedals. - Forged aluminum body - Accepts toe clips - Pedal Body Material: Aluminum - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 335g

Dimension Stem Column Adaptors - Total quill length 180mm - Measurement from minimum insertion to top of steerer adaptor is 118mm - Alloy - Quill insertion diameter: 1-inch

Dimension Two-Bolt Seatposts provide a sturdy and durable saddle perch for cross country and all-mountain riding in three diameters, rigorously tested to ISO 4210 Mountain standards. - Constructed with AL-6061-T6 aluminum - Shot-peened finish - 0mm offset

Dimension 26.0 Stems - Dimension stems are not intended for use with carbon handlebars or carbon steer tubes - Fully forged AL-6061-T6 - 4-bolt handlebar clamp - Weight: 140g-180g

Dimension 25.4 Stem is a fully forged 6061-T6 aluminum stem with 4-bolt handlebar clamp. - 2-D forged AL-6061-T6 - Four-bolt handlebar clamp - 41mm height - Dimension stems are not intended for use with carbon handlebars or carbon steerer tubes - Weight: 130g-180g